Temari #106: a snowman temari with a mini snowball temari

temari-106-snowman-with-mini

 

Temari #106 was inspired by the current season. We have not had a snow yet this winter in our area, but there is still plenty of time in the season for snow.

This temari is really four balls wrapped in white thread, of which only one is stitched as a traditional temari. Three are stitched together to make a snowman. The fourth separate ball is a miniature traditional temari.

Making the snowman and his snowball presented interesting challenges and learning experiences.

four-ball-temari-in-progress

In the previous post, a hint of a snowman to be was given in the picture above. If I had shown them arranged as in the picture below, it would have been obvious what was to become of the three balls.temari-106-in-progress

.

As you can see in the horizontal picture above, the third ball is an unwrapped polystyrene ball. The core of all three are open cell polystyrene balls. Normally, I do not use foam balls for the core of my temari, but this is one of the few exceptions.

The reasons for using polystyrene balls is that they are deformable. I wanted to balls to be slightly flattened so they would “fit” together and so the base of the bottom ball would be flat enough for the snowman to stand without any support.

temari-106-in-progress-3

As for the the use of open cell versus closed cell, the open cell is easier to deform and keep its shape and with the rough surface, the layer of batting and thread sticks nicely to the ball rather than sliding off a smooth surface.

To give a little more stitching room between the foam and the thread, a single layer of polyester batting was wrapped around the sides of the deformed balls. Only on the sides of the middle and bottom balls, as I did not want the batting to round out the flat surfaces.

temari-106-in-progress-2

The third ball for the head was a bit too tiny, so the whole thing got two layers of batting.

The fourth ball does not have a foam core. There is a tiny bell in the center.

Using plastic canvas, an X shape was cut out and the bell tied to the center of the X.

temari-106-in-progress-4

Opposite ends were brought together and sewn, creating a cage for the bell.

temari-106-in-progress-5jpg

A little thread was wrapped around the cage to prevent the layer of batting from getting inside the cage and dampening the sound of the bell.

temari-106-in-progress-7jpg

Finally, more thread was wrapped around the tiny ball to give it a finished layer for stitching into.

The final wrapping also helps to round out the rather lumpy ball. It is still a bit lumpy in the picture below as the wrapping is not quite finished.

temari-106-in-progress-6

The mini snowball temari was marked and stitched as a C8 division. The marking and the snowflakes were stitched using single strand silver embroidery floss. The metallic floss was an incredible challenge to work with. It likes to shred as it is not smooth and does not like to lay flat either since it is not smooth. So the little snowflakes have a bit more character than was intended, making each one more unique.

Working with the metallic thread was rough. So was trying to stick pins in the ball to mark it. The pins kept falling out as I could not stick them in very far due to the bell cage and size of ball. Eventually, I gave up on the pins and just marked it by eye.

temari-106-mini-without-its-snowman

When it came time for assembly and embroidery, I got so wrapped up in the project, I forgot to take more in-progress pictures.

The temari snowman needed some”stick” arms that are posable so he can hold his mini snowball temari. Separate stick arms made of thread wrapped wire bent into arms with three fingers. The thread was white,  a little bit of brown acrylic craft paint transformed them to stick color. To stick arms into the ball, a large needle was used to ream a hole into the ball from the shoulder all the way through towards the waist for each arm and excess wire shoved back into the ball.

The little felt hat and scarf set started off being a crocheted set. My patience for crocheting and the fact that the hat just did not look right, made me switch to felt.

The first felt scarf was a single piece of felt. It was stiff and looked stiff. So, I cut it into three narrow strips to braid. Nice idea, but not long enough. I was working from a small leftover scrap of felt, so I had to cut three more pieces and stitch them to the other three to have three longer ones, ones long enough to braid. And the connection had to be done carefully so as to not be visible. That made a softer scarf and one with more character, especially after adding bells to go with the one on the tip of the hat.

temari-106-in-progress-8

For some reason, the cute grin in the front view ends up looking slightly mischievous in this side view, almost as if he is contemplating throwing the snowball at someone.

 

 

 

 

 

 

Advertisements